Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
Why is my pilot light not staying lit on my furnace?
Some common causes include issues with the thermocouple and pilot tube. The thermocouple detects the pilot light via sensors. … A dirty pilot tube can also prevent the pilot from staying lit. If the pilot tube is dirty, let the furnace cool down and turn off the gas.
What happens if pilot light goes out on gas furnace?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.Should the pilot light always be on in a gas heater?
Most furnaces with electronic ignition have a device called a hot surface igniter. … The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.
How much does it cost to relight a pilot light?
Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100.
How do I know if my pilot light is out?
- Locate the front cover panel on your furnace. It should be a little door that’s easily visible. …
- If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame.
- If you don’t see a flame, your pilot light is out.
- If there is a flame, check the color.
Do I need to turn gas off if pilot light goes out?
Since the thermocouple regulates gas going to the pilot, it should cut off on its own if the pilot ever goes out, but that’s only if it’s functioning correctly. If the thermocouple isn’t working properly, then it’s possible that it’s allowing gas to leak into the very room where the heater is located.How do you reset a pilot light?
- Step 1: Turn off your furnace. …
- Step 2: Locate your gas valve. …
- Step 3: Hold down the red button. …
- Step 4: Light the pilot light. …
- Step 5: Let go of the button. …
- Step 6: Turn your gas back on. …
- Step 7: Turn your furnace back on.
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
Article first time published onHow do you turn on a pilot light?
Turn the gas regulator valve to the “pilot” position. If the water heater has a manual “ignite” button, press that to light the pilot. If it doesn’t have the button, or the button fails, press the regulator valve and hold a grill lighter or long match to the pilot light valve until the pilot ignites.
How do I turn my furnace back on?
- Turn the circuit breaker off and switch the furnace power button off too. …
- Access the pilot light by removing the access panel. …
- Turn the gas control valve off and let the gas dissipate for five minutes before turning it back on in order to prevent a fire hazard.
Where is the reset button on a gas furnace?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
Should I turn off the pilot light on my furnace in the summer?
It’s a good idea to turn off your furnace during hot months. If left on, it will continue to consume energy. The furnace contains some electrical components like sensors that can needlessly draw power throughout the summer. If your furnace has a pilot light, it will use up unnecessary gas during summer when left on.
Who should I call to light a pilot light?
Instead, leave the house and call your local gas company or 911.
How much does a furnace pilot light cost?
A pilot light is a small flame that is kept lit and used as a catalyst for the main burner to be turned on. Natural gas is $0.60 a day, which is $219 a year, and is the average fuel consumption of your standing Pilot light. $657 a year is how much liquid propane is.
Why do pilot lights go out on hot water heaters?
Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple. … Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. A bent or dirty thermocouple.
When should pilot light be turned off?
A little heat is produced when your pilot light is on so turning it off in summer can help reduce the heat inside your home. The less heat there is, the less you have to use your air conditioner needs to cool down the house. You can get savings and conserve energy if you turn off your pilot light.
Can I turn my gas back on myself?
Once the valve is turned off, do not turn it back on by yourself. It must be turned on by a gas company technician. The gas company will likely perform a pressure test on the system and relight all pilot lights in the house as part of turning the gas back on.
Where do you light a pilot?
Step 1: Find the pilot light assembly. It’s usually near the bottom of the furnace and has a gas valve with on, off, and pilot settings. Step 2: Turn the valve to off and wait three minutes.
How do you turn on a furnace for the winter?
- Change Filter. You should check and change your furnace’s air filter every few months. …
- Set Thermostat to “Heat” …
- Clean Burners. …
- Check and Oil Blower. …
- Uncover Heating Vents. …
- Clear Chimney and Vents. …
- Test Safety Monitors. …
- Check for Smells or Noises.
Where is the ignitor on my furnace?
Unscrew and remove the service panel on the side of the furnace and find the ignitor. It is usually mounted on a V-shaped bracket near the gas port. The ignitor has two wires attached to the back of it and has a flat metal tip.
Why is my furnace not heating the house?
Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won’t warm up. If the blower is running but no heat is coming out, replace the filter.
