How do I manually start my hunter sprinkler system

Answer Not Found

How do I turn my hunter node back on?

To turn the controller back on, use the center button to return to the home screen and allow the controller to go to sleep in that position. To turn your controller off, press the button until the icon and Off is displayed on screen. After a short period of time the display will shut off to retain battery power.

How do you program a hunter water system?

Step 1: Set The Current Time. First, you will want to ensure that the current time is correct. …
Step 2: Set the Start Times. Next, turn the dial to “Start Times”. …
Step 3: Set the Run Time. …
Step 4: Set the Watering Days. …
Step 5: Test Coverage. …
Step 6: Finished!

How do I change the battery in my hunter node?

Unscrew the rear body of the NODE body to gain access to the battery compartment.
Insert the battery/batteries into the battery tray and connect to the controller using the battery connector.
Make sure that no water is inside the battery compartment.

How do I reset my Hunter SRC Plus sprinkler?

Press and hold down the , and buttons.
Press and release the RESET button in the lower wiring compartment.
Release the , and buttons. The display should now show 12:00a. m.
All the memory has been cleared and the controller may now be reprogrammed.

How do I set the time on my hunter node?

To set the time and date on the node press the center button, simply scroll through the choices using the left and right arrow buttons and adjust the displayed item using the plus and minus buttons. Push the button until the icon is displayed. All 4 digits will be displayed representing the year.

How do I reset my hunter X2 sprinkler?

Turn the dial to the RUN position. …
Press and hold the program button.
Press and release the RESET button located inside the lower wiring compartment. …
When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.

Why is my controller not starting the watering cycle?

Go to one of the irrigation valves and turn the solenoid 1/4 to 1/2 a turn counter-clockwise. … If the valve opens and sprinklers turn on, your valve is working and you’ll need to check the controller and field wiring. If the valve did not turn on any of the sprinklers, the water to the valves is still off.

How do you test a hunter sprinkler system?

Press and hold the PRG button. The station number will be flashing.
Press the or button to scroll to the station you would like the test program to start with. Use the and buttons to set a run time of up to 15 minutes. …
After a 2 second pause, the test program will begin.

Why are some sprinkler zones not working?

Although it sounds simple, if none of the zones are coming on, first check to make sure the main valve for the system is open. … Failing zones may also be caused by an electrical problem, which can manifest as a problem with the timer, the valve, the solenoid, or the wire. Frequently, a bad connection may be responsible.

Article first time published on

How do I know if my sprinkler controller is bad?

Controller Isn’t Working Properly.
Low or High Water Pressure.
Sprinkler is Stuck or Won’t Come Up.
Puddles on Lawn or Around Sprinkler.
Uneven Spray Patterns.
When to Call a Professional.

How do I reset my sprinklers?

Turn the control dial to the “off” position.
Press the “next” button to access the clear-memory feature. …
Press and hold the “off” button until the display stops blinking.
Turn the control dial to the “run” position.
Press and hold down the “minus” arrow and “prog” buttons simultaneously.

Why won't my sprinklers turn on?

When the sprinkler zones do not turn on at all, it is generally a problem with the electrical signals running from the controller to the valve solenoids. More rarely, it is caused by a faulty valve that needs to be rebuilt or replaced.

How do I bleed my sprinkler system?

Bleed your sprinkler system to avoid any potential problems. Bleeding, or “winterizing” your home’s sprinkler system is one way to protect your sprinkler system from freezing during winter. An easy way to do this is by draining the pipes and then blowing it out to dry with an air compressor.